Matter CC1352 CC2652 Persistent Storage Example Application#

An example test application showing the persistent storage system for Matter on the Texas Instruments CC13X2_26X2 family of Wireless MCUs.

Matter CC1352 CC2652 Persistent Storage Application

Introduction#

This example serves to test the key value storage implementation and API and offers information on proper usage of the KVS system.

This example is enabled to build for CC2652R7 devices. This upcoming devices are currently not yet in full production. For more information on device availability or early access to an engineering build of our Matter-enabled SDK, please reach out here.

Device UI#

Over the debug UART connection you should see the output:

Running Tests:
TestEmptyString(): PASSED
TestString(): PASSED
TestUint32(): PASSED
TestArray(): PASSED
TestStruct(): PASSED
TestUpdateValue(): PASSED
TestMultiRead(): PASSED

This indicates a successful run of the test suite.

Building#

Preparation#

Some initial setup is necessary for preparing the build environment. This section will need to be done when migrating to new versions of the SDK. This guide assumes that the environment is linux based, and recommends Ubuntu 20.04.

An engineering SDK from TI is required. Please request access for it here.
- Follow the default installation instructions when executing the installer.
- The version of OpenThread used in this repository is newer than the one packaged with the TI SDK. Check the following section for a list of changes needed.
Download and install SysConfig (recommended version)
- This may have already been installed with your SimpleLink SDK install.
If you have installed different versions, the build defaults will need to be changed to reflect this in ${chip_root}/examples/build_overrides/ti_simplelink_sdk.gni.

Install Python 3.8 for the GN build system:

# Linux
$ sudo apt-get install python3.8 python3.8-distutils python3.8-dev python3.8-venv
# Distutils listed due to a package manager error on Ubuntu 18.04

You will have to ensure that the default version of Python 3 is Python 3.8.

Check python3 version:

$ python3 --version
Python 3.8.0

If it is not Python 3.8:

$ sudo update-alternatives --install /usr/bin/python3 python3 /usr/bin/python3.8 1

-   This may affect your environment in other ways if there was a
    specific dependency on the prior python3 version (e.g. apt).
    After completing the build process for this example, you can
    revert the python3 version, for instance:

    ```
    $ sudo update-alternatives --config python3
    There are 2 choices for the alternative python3 (providing /usr/bin/python3).

      Selection    Path                Priority    Status
    -------------------------------------------------------------
      0            /usr/bin/python3.8   1          auto mode
      1            /usr/bin/python3.6   1          manual mode
    * 2            /usr/bin/python3.8   1          manual mode

    Press <enter> to keep the current choice[*], or type selection number: 1
    update-alternatives: using /usr/bin/python3.6 to provide /usr/bin/python3 (python3) in manual mode
    ```

Run the bootstrap script to setup the build environment.

$ cd ~/connectedhomeip
$ source ./scripts/bootstrap.sh

Compilation#

It is necessary to activate the environment in every new shell. Then run GN and Ninja to build the executable.

Activate the build environment with the repository activate script.
```
$ cd ~/connectedhomeip
$ source ./scripts/activate.sh
```
Run the build to produce a default executable. By default on Linux both the TI SimpleLink SDK and Sysconfig are located in a ti folder in the user’s home directory, and you must provide the absolute path to them. For example /home/username/ti/sysconfig_1.11.0. On Windows the default directory is C:\ti. Take note of this install path, as it will be used in the next step.
```
$ cd ~/connectedhomeip/examples/lock-app/cc13x2x7_26x2x7
$ export TI_SYSCONFIG_ROOT=$HOME/ti/sysconfig_1.10.0
$ gn gen out/debug --args="ti_sysconfig_root=\"${TI_SYSCONFIG_ROOT}\""
$ ninja -C out/debug
```

Programming#

Loading the built image onto a LaunchPad is supported through two methods; Uniflash and Code Composer Studio (CCS). UniFlash can be used to load the image. Code Composer Studio can be used to load the image and debug the source code.

Code Composer Studio#

Programming with CCS will allow for a full debug environment within the IDE. This is accomplished by creating a target connection to the XDS110 debugger and starting a project-less debug session. The CCS IDE will attempt to find the source files on the local machine based on the debug information embedded within the ELF. CCS may prompt you to find the source code if the image was built on another machine or the source code is located in a different location than is recorded within the ELF.

Download and install Code Composer Studio.

First open CCS and create a new workspace.

Create a target connection (sometimes called the CCXML) for your target SoC and debugger as described in the Manual Method section of the CCS User’s Guide.

Next initiate a project-less debug session as described in the Manual Launch section of the CCS User’s Guide.

CCS should switch to the debug view described in the After Launch section of the User’s Guide. The SoC core will likely be disconnected and symbols will not be loaded. Connect to the core as described in the Debug View section of the User’s Guide. Once the core is connected, use the Load button on the toolbar to load the ELF image.

Note that the default configuration of the CCXML uses 2-wire cJTAG instead of the full 4-wire JTAG connection to match the default jumper configuration of the LaunchPad.

UniFlash#

Uniflash is Texas Instrument’s uniform programming tool for embedded processors. This will allow you to erase, flash, and inspect the SoC without setting up a debugging environment.

Download and install UniFlash.

First open UniFlash. Debug probes connected to the computer will usually be displayed under the Detected Devices due to the automatic device detection feature. If your device does not show up in this view it my be disconnected, or you may have to create a New Configuration. If you already have a CCXML for your SoC and debug connection you can use that in the section at the bottom. Once your device is selected, click the Start button within the section to launch the session.

Select the ELF image to load on the device with the Browse button. This file is placed in the out/debug folder by this guide and ends with the *.out file extension.

Finally click the Load Image button to load the executable image onto the device. You should be able to see the log output over the XDS110 User UART.

Note that programming the device through JTAG sets the Halt-in-Boot flag and may cause issues when performing a software reset. This flag can be reset by power-cycling the LaunchPad.

Viewing Logging Output#

By default the log output will be sent to the Application/User UART. Open a terminal emulator to that port to see the output with the following options:

Parameter	Value
Speed (baud)	`115200`
Data bits	`8`
Stop bits	`1`
Parity	`None`
Flow control	`None`

TI Support#

For technical support, please consider creating a post on TI’s E2E forum. Additionally, we welcome any feedback.

Matter CC1352 CC2652 Persistent Storage Example Application

Contents